Eptfe rad idrofob

Eptfe rad idrofob
Pwodwi Entwodiksyon:
Rezistans: -150 degre ~ 300 degre
​​Breathability:​​ >10,000g/m²·24h
​​Hydrostatic Pressure:​​ >20, 000 mmh₂o
Air pèmeyabilite:<1cfm
Pore ​​dansite: 9b/nan²
Epesè: 30-50 μm
Pwa: 100-300 g/m²
Fòs rupture: 30n/mm
Fòs dlo: 5n/mm
Rezistans UV: UPF 50+
Voye rechèch
Dekri teren
Karakteristik teknik

Expanded polytetrafluoroethylene (EPTFE) is nano-expanded by biaxial stretching to form a 0.1-5μm three-dimensional interconnected microporous structure. Its surface chemical inertness and physical micro-nanostructure work together to achieve super hydrophobic properties (contact angle>150 degre):

Chimik idrofobisite: segondè CF kosyon enèji (485kj/mol), trè ba sifas enèji gratis (18-22 Mn/m), ak natirèlman dlo-pwodui pou repouse moustik.
Idrofobisite fizik: Micropores ak nano-echèl pouse (Cassie-Baxter modèl) fòme yon kouch lè kousen diminye zòn nan kontak solid-likid.

 

EPTFE hydrophobic clothing

Avantaj pwodwi yo

 

Nano-echèl konsepsyon estriktirèl

​Gradient pore size control​: 0.1μm micropores in the outer layer block liquid water, 1μm pores in the middle layer are permeable, and 5μm macropores in the bottom layer enhance air permeability (hydrostatic pressure>30, 000 mmh₂o, ISO 811).
​Self-repairing surface​: Pre-embedded fluorosilicone microcapsules release repair agents after wear, and the contact angle recovery rate is>95% (ASTM D7250).

 

Pwosesis Inovasyon

Fliyò-gratis biaxial etann: dispersants akeuz ranplase PFOA/PFOS (EPA 537.1 limit deteksyon<1ppb), and the stretching ratio is 10:1 to form a nanofiber mesh structure.
​Plasma modification​: Ar/O₂ plasma etching enhances surface roughness (Ra>1μm), ak ang kontak la ogmante a 160 degre (verifikasyon SEM).

 

Verifikasyon Idrofobisite ki dire lontan

​UV aging​: After 5,000 hours of QUV, the contact angle is >145 degre, ak lavi a idrofob se 5 fwa pi long pase sa yo ki an penti PU tradisyonèl (ASTM G154).
Endistriyèl lave: Apre 50 fwa nan 80 degre machin lave, pouri anba tè a pèfòmans idrofob se<3% (ISO 6330), and there is no plasticizer precipitation (GC-MS detection).

Faktori nou an

 

Faktori nou an te konsantre sou pwodiksyon an nan E-PTFE ak materyèl konpoze pou plis pase 10 ane. Nou entèdi chwazi matyè premyè, entèdi kontwòl pwodiksyon, ak entèdi enspekte bon jan kalite. Nou gen yon ekip R & D pwofesyonèl ki ka Customize R & D epi yo gen koperasyon alontèm ak Swèd. Nou redwi depans nan pwosesis optimize ak gwo-echèl pwodiksyon otomatik. Nou te genyen konfyans nan mache a ak-wo kalite, pwodwi Customized ak atitid pwofesyonèl ak konsantre. Nou sensèman envite kliyan yo konsilte epi mete lòd.

Kaili eptfe equipment
Kaili eptfe factory

 

Baj popilè: Eptfe rad idrofob, Lachin Eptfe manifaktirè rad idrofob, founisè, faktori

Voye rechèch
Epi kòmanse RFQs ou kounye a.
Kontakte nou